|
The new Hover Trimmer String Trimmer Line Replacement Kit Fits Easily Onto Any Straight Shaft Weed Trimmer Machine Measuring Up To 28mm In Shaft Diameter. Simply remove the existing string line trimmer head and replace with the easy fit Hover Trimmer Kit replacement head. Please NOTE: Read the manufacturer's instructions supplied carefully and pay close attention while operating the Aero-blade. Before beginning work with the Hover Trimmer, warm up the trimmer motor for around 2 minutes. Then accelerate the engine for 5 seconds before putting the blade parallel to the ground. The propeller blade will create the anti-gravity propulsion that keeps the blade at 2-3 cm parallel to the ground on a cushion of air. Upon operating the trimmer engine at a consistent velocity, this results in reduced fuel consumption. DO NOT use rapid scything movement (more than 10/20 cm) as this can be dangerous and cause blade damage. Take responsibility and operate weed trimmer machines with care and attention at all times. To maintain PULVERIZATION results, keep the blade clean and sharp; slightly tilt the blade in the direction of the movement. Please DO NOT use a warped, cracked, broken or damaged blade. Always operate the Hover Trimmer Application with a maintained cutting blade. The rotating Aero-blade must not come in contact with stones, metal or hard objects, as this can cause blade damage. If the Aero-blade starts to shake or vibrate, turn off the engine and check the whole unit. Do not operate it until the trouble has been properly corrected. Follow these instructions: (a) Read the manufacturer's instruction manual (b) Check if the blade is properly assembled and firmly tightened. (c) Check if the blade is balanced by starting the machine and running the engine at full acceleration for around 1 minute. If vibration is still present please stop the machine and carefully remove the blade and insert the small red circular plug provided into the blade hole (See below Fig 28 above). This should eliminate any previous vibration issues and the Hover Trimmer machine can now be operated normally. |
|
|
|
|
| HOW TO ASSEMBLE YOUR NEW PATENTED HOVER TRIMMER SYSTEM - FIRSTLY - DISMANTLING YOUR EXISTING ROTATING LINE OR BLADE HEAD - |
|||
| 1 |  |
2 |  |
| Starting point: – Normal Configuration | Pics 2 , 3 & 4 Dismantling Line Head: | ||
| 3 |  |
4 |  |
| Lock the gear shaft by inserting a screw driver into the holder on the gear and turn the Line Head in a clockwise direction. Or you may have a special tool that came with your trimmer. | |||
| 5 |  |
6 |  |
| Pics 5, 6, 7 & 8 - Removing two Holders - If present remove the anti-tangling cup | |||
| 7 |  |
8 |  |
| 9 |  |
10 |  |
| Pics 9 & 10 Dismantling cutting head from the shaft Remove the bolts/screws screwed into the shaft then loosen the main bolt of the cutting head. The cutting head easily will come out from the shaft |
|||
| 11 |  |
12 |  |
| Pics 11 & 12 - Dismantling Guard Remove all the bolts on the Guard and remove the Guard from the shaft |
|||
| - NOW TO ASSEMBLE YOUR HOVER TRIMMER HIGH SAFETY DOME HEAD - | |||
| 13 |  |
14 |  |
| Pics 13 & 14 Loosen the Cover nuts with the wrench supplied with the Cover then raise the red guide tabs | |||
| 15 |  |
16 |  |
| Pics 15 & 16 Insert the Cover into the shaft (DO NOT THIGHTEN THE NUTS) Next, reassemble the Cutting Head. Check that the bolts/screws are firmly tightened | |||
| - NOW TO ASSEMBLE YOUR HOVER TRIMMER PATENTED BLADES - Note: the blade is assembled in the same way as a normal blade |
|||
| 17 |  |
18 |  |
| Pics 17 & 18 Insert the Holder (Pic17) provided with the blade housing. Now position the propeller in the blade housing of the cutting head with the blade nuts upwards | |||
| 19 |  |
20 |  |
| Pics 19 & 20 Insert the metal holder (Pic 19) and the nut (or bolt) already supplied with the Hover Trimmer on the blade. Now tighten the nut (or bolt) firmly counter clockwise (locking the gear shaft by inserting a screw driver the same as when you dismantled your existing line head | |||
| - TIGHTENING YOUR HOVER TRIMMER HIGH SAFETY DOME - | |||
| 21 |  |
22 |  |
| Pics 21 & 22 After tightening the propeller blade, position it perpendicularly to the line of the shaft. (Pic 21) Slide down the Cover over the blade keeping the sides of the cover parallel in distance to the blade on each side. Leave approx 4 cm clearance between the blade edge and the cover edge (Note: Check that the black rubber washer is in the correct position as shown in Pic 22 | |||
| 23 |  |
24 |  |
| Pics 23 & 24 - Stongly tighten the nuts and the internal screw of the red guide tabs. ENJOY YOUR NEW PROFESSIONAL HOVER TRIMMER |
|||
|
|
|||
| - MAINTAINING YOUR HOVER TRIMMER PATENTED BLADE - | |||
| 25 |  |
26 |  |
| Pics 25 & 26 Your new Hover Trimmer System also comes with a blade sharpening file. Before starting work sharpen the blade by filing the propeller it in each upper sharp side throughout the length by rapid movement (3-4 times per side). KEEPING THE BLADE SHARP will protect it from rapid deterioration. | |||
| 27 |  |
28 |  |
| Pics 27 & 28 - Use the file upside down (Pic 27). To reach equilibrium/balance sharpen the heavier side of the blade (Pic 28) |
|||